Users Online Now:
2,192
(
Who's On?
)
Visitors Today:
2,047,678
Pageviews Today:
2,842,525
Threads Today:
685
Posts Today:
13,489
09:35 PM
Directory
Adv. Search
Topics
Forum
Back to Forum
Back to Thread
REPLY TO THREAD
Subject
How to use Colloidal Silver as Medicine
User Name
Font color:
Default
Dark Red
Red
Orange
Brown
Yellow
Green
Olive
Cyan
Blue
Dark Blue
Indigo
Violet
Black
Font:
Default
Verdana
Tahoma
Ms Sans Serif
In accordance with industry accepted best practices we ask that users limit their copy / paste of copyrighted material to the relevant portions of the article you wish to discuss and no more than 50% of the source material, provide a link back to the original article and provide your original comments / criticism in your post with the article.
[quote:abeland1:MV8yMzczMTUzXzk0NTkxNjg4XzM5QTkzQkIx] https://theartofmakingcolloidalsilver.com/the-csg1-generator-2/ To check if we are done with the process, place your finger on the generator and gently move the position of the wires, as shown in the picture above. Observe the change, if any, in the brightness of the LED. If the LED dims noticeably when we moved the wires in the water, we are not finished. It is important to gently move the position of your generator the when you see the red LED glowing brighter during the process. [imgur]https://imgur.com/a/aPHouge[/imgur] In this picture we can see that the LED is much less bright after we have moved the position of the silver wires. [imgur]https://imgur.com/a/ZjlnDAK[/imgur] This is confirmed by measuring the PPM of the water in the glass. It reads slightly over two PPM. So we continue the process. [imgur]https://imgur.com/a/JfyKRdo[/imgur] We are now 3 hours into the process, our conductivity meter reads 5 PPM, and we continue the process. [imgur]https://imgur.com/a/CTa6STN[/imgur] We are now five hours into the process and we can see that the LED is once again at full brightness. At this time, we will once again do the finger test. We observe that the LED’s brightness remains the same when we press on the generator. This means that we have achieved well over 10 PPM strength of colloidal silver. Please note that your process could be less than 5 hours depending on the quality of your distilled water. [imgur]https://imgur.com/a/1dBuEB3[/imgur] We confirm this with the use of our electrical conductivity meter. It reads 15.1 PPM. Please note that the reading will vary depending on the quality of your distilled water. We are now finished with the process of making our colloidal silver. [imgur]https://imgur.com/a/b45LSRV[/imgur] Remove the generator from the water and clean the silver wire with a green scouring pad supplied. Two or three swipes should be sufficient. [imgur]https://imgur.com/a/Cnlul5f[/imgur] We now use our red laser pointer included with the kit to confirm the fact that we have made actual particles as well as the ions that are measured by an electrical conductivity meter. If we include the particles in our measurement, which are not shown by conductivity, the true PPM would be 17 to 18 in parts per 1,000,000. In the days before good laser pointers were available; the only way we had to ensure that we had made larger particles was for the water to turn yellow. You will find many people who still believe that Colloidal Silver should be yellow because of this. The fact is that a yellow color Colloidal Silver indicates particles over 40 nanometers in size. Clear color, like water, means smaller particles. Small particles are better. Some people refer to silver particles this small as nanosilver. Filter the colloidal silver to remove any large particles that may have formed. A coffee maker filter of the unbleached variety is perfect for this. We now have 12 ounces of better colloidal silver than can be purchased at a store. We can do this hundreds of times before we have to buy more silver wire. [/quote]
Original Message
DISCLAIMER:
This is non-professional opinion and should not be taken as advice from a medical doctor. This concerns typical viruses/bacterial infections such as the common cold, or as first-aid, not serious disease.
------------------------------------------------------
Colloidal silver is a safe, natural antimicrobial. It will not interfere with pharmaceuticals and
will not turn your skin blue
, as long as you don't chug gallons of it or use a poorly-made colloid (I recommend [
link to www.mesosilver.com
]
It works best when used as soon as symptoms begin to appear
, and is effective as long as it can touch the germs.
Eyes
-- Put a drop or two in the eye to cure infection
Nose/Sinuses
-- Get about a half-teaspoon or so in a dropper. Lie down on your back at the edge of a bed or couch and let your head drop back so the top of your head points straight down. Put a couple drops in each nostril and wait for the (possibly intense) pain/burning to stop. Then repeat till the silver is gone. Quickly turn over and face the floor so the silver drains into the front sinuses behind the eyes and cheekbones. Then get up and let the silver drain into your throat; it's perfectly safe to swallow. Repeat twice a day till symptoms are gone.
Throat
-- Gargle several times a day.
Lungs
-- Use a half-teaspoon or so in a nebulizer to treat bronchial or lung infections, even pneumonia.
Skin
-- Put a drop or so on a bandage and apply to wounds.
Digestion
-- Swallow several tablespoons twice a day, preferably when you won't be eating or drinking for at least an hour; bedtime is best.
This is a known safe antimicrobial, even for children and babies.
Pictures (click to insert)
General
Politics
Bananas
People
Potentially Offensive
Emotions
Big Round Smilies
Aliens and Space
Friendship & Love
Textual
Doom
Misc Small Smilies
Religion
Love
Random
View All Categories
|
Next Page >>